+8613064022215
When using a manual pump， first return the oil valve knob and tighten it clockwise. Press the handle to slowly lift the bridge.
1In general， there are several reasons for hydraulic cylinder oil leakage: damage to the oil seal ring on the cylinder， etc. The cylinder body of the oil cylinder is damaged. Oil leakage caused by defects such as air holes， sand holes， and shrinkage in the guide sleeve.
iParisProduct features: Fully hydraulic drive，Container boarding bridge easy to operate and reliable to operate. Manufacturers of specialized hydraulic lifting platforms，HuozhouMobile hydraulic boarding bridgeMultiple precision requirements need to be met hydraulic elevators， rail type cargo elevators， mobile elevators， rail type elevators， and hydraulic lifting cargo elevators for factory warehouse workshops.
The height of the loading and unloading channel is fixed， but the height of the carriages is different. There is always a certain height difference or gap between the transportation vehicle and the loading and unloading platform. The transfer forklift can quickly enter and exit the transport vehicle for loading and unloading. Fixed boarding bridges are used to provide reliable connections. Fixed boarding bridges are used to provide reliable connections. Raise the rear of the boarding bridge and move it on the vehicle. Land stripping and regular maintenance system for boarding bridges: This system is specially formulated to enhance the effectiveness of boarding bridges and prevent changes.
OHaslevRelease the start button， the fixed boarding bridge will automatically descend， and the circuit board will be placed at the rear of the truck. After completing the above steps， it can be loaded and unloaded.
NlWhen maintaining，Container boarding bridge maintaining， and cleaning the interior of the hydraulic boarding bridge， it is necessary to use a support rod to support the adjustment plate and strictly prevent other objects and personnel from colliding with and touching the support rod! Avoid accidental injury accidents. The green belt trimming machine mainly completes the trimming of the top， side， and lawn of the green belt through the rotation of the head， side， and bottom films. The machine has a simple appearance， is very convenient to move， is easy to operate， and can adjust the height freely. It can also trim the top，Container boarding bridge side， and lawn of the green belt at the same time，HuozhouMobile hydraulic boarding bridgeMultiple precision requirements need to be met saving a lot of manpower. The height of the bridge loading and unloading platform is fixed，But the height of the carriages is different. There is always a certain height difference or gap between the transportation vehicle and the loading and unloading platform. Forklifts cannot directly enter or exit goods. Professional sales of boarding bridge factory safety， environmental protection， and economy! Our products are exported to foreign countries and highly trusted
Secondly， but also the inability to support the entire operation process!
When the lowering valve is opened and the lowering button is released use an ammeter to check if the lowering valve is energized. If there is no power， check the route and perform fault detection; If there is electricity， clear the common faults of the lowering valve itself. The electro-hydraulic directional valve of the descent valve must be kept clean and easy to move.
rThe lip plate is connected to the platform using a full length shaft， which has high strength and good reliability.
Z. Platform side boarding bridge: The platform side boarding bridge is directly installed at the front edge of the loading and unloading platform. There is no need to excavate or reserve pits on the loading and unloading operation platform，Boarding bridge_ Mobile boarding bridge_ Mobile hydraulic boarding bridge_ Fixed boarding bridge - boarding bridge factory and there is basically no change to the building structure. During construction， the factors of loading and unloading operations were not taken into account. The platform type loading and unloading bridge serves as a remedial solution and can also meet the requirements for loading and unloading operations into truck carriages.
SInstallation conditionsThe characteristics of the bridge deck are as follows: the electric control operation is extremely simple， and the bridge deck will automatically rise by pressing the button; Release the button， adjust the board to lower by its own weight， and place the loose leaf landing board on the truck to use.
hMThe problem of sealing ring damage is common in almost all hydraulic systems， such as oil cylinders. It may be due to poor quality of the sealing ring itself， insufficient compression of the sealing ring， etc. When the sealing ring is lifted and lowered for a long time， it causes varying degrees of wear and tear on the sealing ring. This is a common cause， causing gaps in the sealing performance of the sealing ring， leading to oil leakage. At this time， it is only necessary to find the damaged sealing ring and replace it with a new one.
The hydraulic boarding bridge service platform and lip plate will be connected to the short shaft during operation， enabling the bridge to choose bridges with high compressive strength and high reliability during the application process. The equipment design scheme will use high toughness; U-shaped” Beam. That way， to a certain extent， ensures long-term deformation free operation under high loads.The viscosity size of the hydraulic oil used immediately affects the rate of increase. Hydraulic oil belongs to the category of organic chemical products as raw materials， which can cause poor physical and mental health hazards. Immediate contact with the skin and eyes can cause significant damage. When applying hydraulic oil， # is used in summer and # is used in winter， and it is replaced twice a year. When disassembling and replacing， it is important to ensure that the hydraulic oil is completely discharged into the container， it will not lift. The fundamental reason is that each boarding bridge often has its own rated cargo capacity. Once it is overweight and lifted， there will be a situation of weak lifting or inability to lift. Therefore it is effective to ensure that the goods are not overweight during transportation. With the rapid development of the times， the logistics industry has also developed rapidly in various industries. Fixed lifting platforms and hydraulic boarding bridges have become the preferred auxiliary handling equipment for logistics enterprises. Lets talk about the service life of hydraulic boarding bridges for these handling equipment.
Equipment maintenancerThe oil cylinder and the oil cylinder of the boarding axle are used frequently， and the good thing is to use imported sealing rings. Manufacturers such as Hengyu， Daewoo， and Blacksmith are all relatively mature brands in China.
OThe fundamental load literally， refers to the self weight load of the metal structure， organization， power， as well as the lifting load of the lifting mass of the lifting channel. It also includes the impact load that occurs when operating on uneven roads， as well as the horizontal load caused by organizational braking. Can achieve different application effects. The fixed hydraulic boarding bridge is designed based on the equipment environment of the elevator. The fixed hydraulic boarding bridge can be used in conjunction with its own application requirements， ensuring that the axle and carriage are securely connected for travel. On a French container vehicle， the iron hook on the boarding bridge is attached to the dedicated hook of the quasi container vehicle; On a regular container truck， the iron lock on the boarding bridge is tightly wrapped around the iron frame fixed at the rear of the car and locked with a lock. The hydraulic support (no， and no) at the junction of the inspection bridge and the vehicle can be secured， and can withstand the weight of forklifts and trucks. If not， unloading， and transporting goods， the height of the adjustment plate on the boarding bridge should be adjusted to ensure a smooth overlap with the rear panel of the car. The iron chain on the boarding bridge should be firmly bolted together with the car. The mobile hydraulic loading bridge is widely used in cargo platforms and mobile loading and unloading places without loading and unloading equipment， and is an auxiliary equipment for cargo loading and unloading used in conjunction with forklifts. With the help of a mobile loading bridge， forklifts can directly enter the interior of car containers for bulk loading and unloading operations.
mUThe front of the conditioning board base is designed with an open design， making it convenient and quick to organize clutter
The problem of sealing ring damage is common in almost all hydraulic systems， such as oil cylinders. It may be due to poor quality of the sealing ring itself， insufficient compression of the sealing ring， etc. When the sealing ring is lifted and lowered for a long time it causes varying degrees of wear and tear on the sealing ring. This is a common cause， leading to oil leakage. At this time causing gaps in the sealing performance of the sealing ring， it is only necessary to find the damaged sealing ring and replace it with a new one.
